FireBee_Setup/mint/1-19-9ef/mint.cnf

# ---------------- FreeMiNT configuration file ---------------------
#                          for FireBee
#

# The "set" directive controls the behaviour of the mint.cnf parser.
# It accepts one of three parameters:
#
#set -q - silent output (+q for verbose output)
#set -v - print command lines (+v don't)
#set -c - control interpretation of escape sequences

set -q

# The include command allows you to include other files while the
# mint.cnf file is being interpreted. The included file will be
# interpreted as a part of the mint.cnf file.

#include u:/c/mint/vars.cnf

# The smaller the KERN_SLICES value, your processes have faster
# response time but the general performance is worse. Very fast
# machines however, may benefit from setting 1 here.

#KERN_SLICES=2

# KERN_DEBUG_LEVEL controls output of global debugging information.
# The higher the level, the more stuff MiNT will spew about about
# what it's doing.
#
# The average user doesn't want to hear about this stuff, so the
# default is 1, i.e. display ALERT messages only. Note that you need
# a debug kernel to get more: normal kernels do not contain so much
# debug information.
#
# KERN_DEBUG_DEVNO is the BIOS device number to which the info
# should be sent.
#
# Devno can be: 0=printer, 1=aux/modem, 2=screen (console), 3=midi,
# 4=keybrd, 5=raw.
#
# The default is the console.

#KERN_DEBUG_LEVEL=1
#KERN_DEBUG_DEVNO=2

# KERN_BIOSBUF controls how BIOS I/O is performed. Normally, MiNT
# tries to buffer this to provide a (considerable) improvement in
# speed. However, some applications may get upset by this.
#
# KERN_BIOSBUF=NO turns off all buffering for maximum compatibility.
# The default is YES.

#KERN_BIOSBUF=YES

# KERN_SECURITY_LEVEL= enables the appropriate security level:
#
# 0 - recommended for single user setups, like MultiTOS (default).
# 1 - recommended for multiuser setups, like KGMD.
# 2 - full protection, unsupported by software, thus discouraged.

#KERN_SECURITY_LEVEL=1

# KERN_MPFLAGS controls the memory protection behaviour. Its argument
# is a bitfield. Only the bit 0 is defined: 1 means, that more strict
# model of the protection should be enabled. Some programs may
# refuse to run, so the default is 0.

#KERN_MPFLAGS=1

# TPA_FASTLOAD=YES forces fast loading (without zeroing all the
# memory) for all programs. This defines a default state, that can be
# modified later via appropriate kernel calls (use MiNT Setter
# utility to toggle it later when neessary, without reboots).
#
# TPA_FASTLOAD=NO (default) means that the information from the
# program header will be used to decide (this is like TOS does).

TPA_FASTLOAD=YES

# Set maximum additional TPA size for new processes
# (in kilobytes). The default is 1024. Better keep it low (1024 is
# what we call low) if your machine has 4 MB RAM or less.

TPA_INITIALMEM=8192

# FS_VFAT= enables VFAT extension for selected drives.
# The VFAT extension is disabled by default.
#
# If you use both TOS and MiNT, better don't enable VFAT extension
# on your boot drive.

#FS_VFAT=D,E,F,G
FS_VFAT=A,C,D,E,F,G

# FS_VFAT_LCASE=YES tells the kernel to return lowercase filenames
# from VFAT directory searches. The default is NO.

#FS_VFAT_LCASE=YES

# FS_WB_ENABLE= enables write back cache for selected drives. The
# write back cache is disabled by default. Also, it does not have
# any effect for TOSFS drives.

#FS_WB_ENABLE=A,C,D,E,F,G,H,I,J

# FS_CACHE_SIZE= specifies the size of disk cache in kilobytes for the
# internal caching module. Default is 128.

FS_CACHE_SIZE=2048

# FS_CACHE_PERCENTAGE specifies the size of the disk cache (in
# percents) to be filled with linear reads. The default is 5.

FS_CACHE_PERCENTAGE=10

# FS_UPDATE= set update time for system update daemon in seconds
# default is 5, it isn't recommended to use a value less than 4.

#FS_UPDATE=10

# Software write protection on filesystem level.

#FS_WRITE_PROTECT=R,S

# FDC_HIDE_B= tells the MiNT to remove floppy drive B: from the
# system.
# It is useful on single floppy systems to get rid of "Insert
# disk B: into drive A:" messages from the AES. Default is NO.

FDC_HIDE_B=YES

# PROC_MAXMEM= gives the maximum amount of memory that any process
# may use (in kilobytes). The default is to make this unlimited, but
# if you have a lot of memory and/or programs that grab more memory
# than they should, try setting this.
#
# E.g. to limit processes to 4096K of memory, remove the '#' at the
# beginning of the next line.
#
# WARNING: the process will not be allowed to allocate memory beyond
# the limit, and it won't "see" more memory as available from the
# system.
# Please understand that programs like "free" (or any other that
# interrogates the system how much memory is available) is a process
# as well, thus it will undergo this limit too!
#
# Decent shells (desktops) allow you to limit the maximum amount of
# memory independently for each program.

#PROC_MAXMEM=4096

# Three commands, that define output files for RS-232, console and
# printer devices. The argument for each one must be a pathname.
#
# For best results, the convention u:/drive/pathname should be used
# for all specified pathnames from now on.

#GEMDOS_AUX=u:/c/mint/aux.out
#GEMDOS_CON=u:/c/mint/con.out
#GEMDOS_PRN=u:/c/mint/prn.out

# End of kernel settings

#
# -------------------------- Commands ------------------------------
#

# Here are some commands that you can give to MiNT:
#
# alias d: path -- make a fake "drive" that actually points to the
#                  given path
# cd path       -- changes MiNT's default directory
# echo message  -- print something on the screen
# exec program  -- runs a program; you must give the complete path
#                  and file extensions (e.g. c:/bin/echo.prg)
# include file  -- include another portion of the MINT.CNF file.
# sln path link -- make a symbolic link named "link" pointing to
#                  "path". "link" must be on drive U: for this to work
#
#-------------------------------------------
#
# Set up system symbolic links
include u:/c/mint/sys.cnf

# Basic environment variables
setenv PATH /bin;/net
setenv SLBPATH 'c:\mint\slb\;c:\gemsys\xtension\;c:\gemsys\slb\'
setenv HOME u:/home
setenv TMPDIR u:/tmp
setenv HOSTNAME firebee
setenv USER root
setenv LOGNAME root
setenv SHELL u:/bin/bash
#
#
# Check filesystems.
#exec c:\mint\tools\fscheck\vfatfsck.ttp c:

# Initalize network.
include u:/c/mint/network.cnf

# Run MGW (Draconis gateway for MiNTnet)
exec u:/c/mint/tools/mgw/mgw.prg

# Run GLUESTIK to MinTNet gateway
exec u:/c/mint/tools/gluestik/gluestik.prg --force

# The best option is to have INIT= command here, after all pathnames
# are already set up by commands above.
#
# If the MiNT is supposed to execute GEM, you should specify the full
# path and filename like that:
#
#GEM=u:/c/mint/1-19-9ef/xaaes/xaloader.prg

# You can also request MiNT to execute the TOS AES residing in ROM.
# WARNING: this is not recommended, you should use a GEM version
# instead, that is multitasking friendly.
#
#GEM=ROM

# Otherwise, if your init program is not GEM, you should use INIT= as
# follows:
#
INIT=u:/c/mint/1-19-9ef/xaaes/xaloader.prg
#INIT=u:/c/mint/sys/bin/bash

# If you leave both commands above commented out, the MiNT will
# attempt to execute a file called `sh.tos' found in the system
# directory (the same where the mint.cnf resides), and if this
# fails, the internal minimum shell will be executed.
#
# The "echo" command is really straightforward.
#
echo Setup complete, now booting the system...
echo